Stan
Forum Replies Created
- Posts
-
My Eclipse got a new panel under warranty. I watched the repairman do the swap. I would not attempt unless you have specific instructions. It wasn’t just taking off the old panel and putting on the new one. It was taking off the old panel, swapping a bunch of parts from old to new, and then puting the new panel on. I mean none of it looked too difficult – no special tools, just a screwdriver / maybe a torx wrench and removing / adding the panel is 2 person job lifting and centering, However, knowing which parts need to be swapped in which order would probably be hard to figure out and easy to miss something.
I assume the ads are embedded in the radio stream by the radio station. For one station, I mostly get ads about the audicy app which is the preferred app for the station. For the local classical music station, there’s always an ad for a bank that is major sponsor. It’s also doesn’t happen with all stations.
Interesting about the Tune-in app. I almost always get ads when I use GVA which usually uses Tune-in. For example, I’ll get an ad sometimes before I play Radio Paradise on Tune-in, but never B&O Radio. I would say it definitely varies by station and possibly location.
Stan
That looks very nice. Good job! You’re inspiring me to do something more than digging out my phone all the time.
Stan
Pressing the Join button on the Balance plays the last source I played on the Balance. I must have enabled the new interface? I haven’t paid too much for attention to these interfaces since usually I use the app or my Essense remote since I find the the “physical” buttons on the units to be too finicky.
Figured it out…
It is the “Product Controlled by Apps” setting. I had it set to “ML Audiomaster” (ML source plays automatically) when it should be “BeoLink Converter NL/ML speakers” (ML source does not play automatically). Since I don’t have speakers connect to my BLC, I thought I needed to select the “ML Audiomaster”, but this is not true.
When I start a ML source on the BLC, the Balance can join. When I start a ML source on the BS1, the Balance cannot join even though it shows up in the multi-room device list.
Next question is that when I start a source on the BLC, the audio also plays on the speakers of the ML device. For example, I select N.Music on the BLC, my BS5 starts playing on its connected speakers. I thought it was supposed to behave like a BL3500 or BL Active where I select N.Music and it only plays on the BL3500 / BL Active (unless I also activate the BS5 speakers).
Is there a BLC or BS5 config setting somewhere that can make it not automatically play when the BLC source is selected? This is annoying because the audio on the NL side is delayed from the ML side.
I can see the Balance in the multi-room display under the BLC in the app. However, when I select it, it doesn’t “join”. The app thinks about it for a few second, but does nothing.
Can you send ML sources to your Emerge?
My family has long given me crap about how *hard* it is to use B&O equipment. My son likes to say that it is annoyingly different for the sake of being different… as in, there’s no value in its differentness. I learned a long time ago that it’s a waste of time to argue about UXs… people like what they like (and dislike what they dislike).
My answer to them has always been that B&O is mostly easy and intuitive if you have never used any AV equipment before. So, step 1 to learning B&O is to forget everything you already know about AV equipment. Most of these UX “standards” that Luke’s hand mentions probably were not standard when B&O first decided that a red dot means “standby” and “Go” means “Play”. I know my first turntable and cassette deck used “Play”… I don’t recall the triangle showing up until maybe the walkman, and then it took 5 – 10 years before it became “standard” (of course, I’m getting on in years so my memory may be spotty). Having chosen their path back in the 70s, they stuck with it.
About the “no thought” on the button layout of the BeoRemote, from all the examples shown on this thread, only the B&O remotes have the numbers in a logically useful order. Everybody else goes from 1 at the top left to 9 that the bottom right. Meanwhile, B&O has 1 at the bottom left and 9 at the top right. Why does this matter? At least in my experience, I select a lot more channels that start with 1 – 3 vs. 4 – 9. Therefore, on average, my finger doesn’t have to reach as far vs the “standard” numeric layout.
All of my B&O Radio devices are working fine. This includes both Mozart (Balance) and older (BS2 gen1). I guess I’d try rebooting the core and/or stage.
Not exactly on topic, but I just lost 2 of my favorite stations. They are still in the list, but when select them, no music. I’m guessing the station owners are closing down the “free” streams to push us to monetization.
When my motherboard failed, it failed. There was nothing intermittent about it. Then again, the last time I had a HD fail (in a laptop, not the BS5), it also was not intermittent. In my experience, intermittent problems are often bad cables or bad connections (or most commonly software). I did once have an intermittent problem with a macbook that was solved with a new cable to the HD.
Unfortunately, I don’t know anything about how to read the crashdumps or what they mean.
Oops, I guessed wrong about the Beoremote behavior. The “my buttons” on the Beoremote one are automatically linked to the “my buttons” on the BS1. If you program a button on the BS1 to “get the weather”, pressing the corresponding button on the remote will get the weather (regardless of microphone status). If you long press the Beoremote mybutton to “program” the button to the current settings (as you do on non-GVA devices), it behaves the same as long pressing the button on the BS1: it prompts for you to speak another command regardless of whether the microphone is muted or not.
I don’t know what happens if you’ve never registered the device to Google as mine is registered and I’m just turning the microphone on and off. I don’t feel like re-setting up my BS1 just to test this since I don’t mind using Google – like I said, it’s helpful in the kitchen when the hands are wet or dirty (and we’re careful to only discuss our plans for illegal activities in other rooms without listening devices) 😀
9 time out of 10, it’s the mother board… unless you’ve already had this repaired. My repair guy told me the original board had some issues with heat so if you operated your BM5 is an warm environment or the ventilation wasn’t good, then it tended to fail. The only solution I’m aware of for this is to get the part replaced by B&O.
It could also be the hard drive – these fail too. It’s not hard to replace the hard drive if you have a backup of the old one. If you search the 2012 – 2022 forum archive, you can find threads about doing this. You will want to find the service tool which has been posted to the forum in the past. This gets loaded to a USB drive and you boot the BS5 from it, and then can rebuild a new disk. I guess I’d start here. If the BS5 will not boot from the service tool USB drive, then it’s probably the mother board that has failed.
Just to be clear, you can do the initial wifi setup without Google. I was just pointing out an issue that came up here recently with respect to changing the wifi network after this initial configuration. You need to go into Google to do this, but you can always setup from scratch if you need to change the wifi network and don’t want to use Google.
That’s an interesting question about Beoremote operation. My guess is that the remote “my buttons” work the same on a Google vs non-Google Beosound, especially if you never go through the Google setup. That is, you would use the app to select a B&O Radio station or other source, then program the remote mybutton… so you would get your 4 buttons without Google, but they are on the remote rather than the unit.
I do have a BeoRemote so I will test this when I get a chance.
The center button action is selectable in the configuration menu. It is either:
Single tap toggles between sound and silence. Double type cycles sources.
Or
Single tap to Play / Pause. Long press to Join in on a multiroom experience.
I turned off the microphone on my BS1 GVA today, and it announced that the microphone was off, and the 4 little dots that blink during a normal GVA voice command turned red. The 4 “my button” dots disappeared leaving just the center dot and the red little dots glowing steadily.
It stayed this way through power cycles and extended off time and operated just like a non-GVA BS1. That is, it remembered the setting – it’s not like you need to do this each time you turn it on. Also, there was no periodic “microphone is off” announcements.
When I turned the microphone back on, the red dots disappeared, and the 4 my buttons reappeared and were programmed as before.
As far as I can tell, you will still need Google if you want to change your wifi network (without going through a new setup) or connect bluetooth devices. I see no settings for those in the configuration menus.
As far as I know, it’s still the case. You cannot use the buttons to activate B&O Radio, but rather it will use TuneIn or Audasey or whatever service Google can use in your country. In the US, I get some stations via TuneIn others via Audasey.
Also, if you have other Beosounds, you can’t join to a Google started audio stream unless you set it up via Google home. The BS can join to other devices – so you can start a B&O Radio source on a different device, and press the middle button and it will join. If you start the B&O Radio source on the BS1 using the B&O App, then the others can join… just not when you use voice or my buttons (which are essentially saved voice commands).
You can turn off Google, but I think that just turns off the voice command capability. I also think I’ve read that it gives you an annoying warning from time to time that the microphone is turned off.
Also, bear in mind that there are certain configurations that can only be done through Google. For example, for some reason, bluetooth and wifi setup are done through Google Home rather than the B&O App.
I thought there was an option to get a non-Google BS1, but I might be confusing that with other Beosounds.
I have a Google enabled BS1. Maybe I will play around with it so I can answer more definitively about what happens when Google is turned off… as I’ve never turned it off because it’s pretty convenient in the kitchen when your hands are wet or messy and you don’t want to touch the machine.
I also have a stereo pair that I used in my office for about 6 months. I usually did NOT use the app to pair. I found it was easier to use the button method. I also used them with my computer. Also, to use them as a speaker phone, they must not be stereo paired.
Yes, they were a little wonky from time to time, and had to be setup each time they poweed off – you can pause for less than 10 (maybe 15) minutes and restart in stereo, but once they power off, you need to repair.
Not to make excuses for B&O, but every bluetooth device I’ve used is wonky from time to time so maybe I have a higher tolerance for that stuff. I also thought it had something to do with all the other electronics I have running in my office. I’ve had some devices that I had to leave the office to pair successfully.
They do sound surprisingly good so, to me, it was worth the occasional dropouts, re-pairing, etc. However, I do see that if I had these in my living area I’d not like to pair them every time. So, yeah, not for everyone or every use case.
I looked through settings for my Balance, and it looks like Mozart based products need to be re-configured from start to change their network. I’d be happy to learn otherwise, but I don’t see a “Configure” menu item like on the ASE equipment.
Not sure what you are asking. If you buy a new LG, then you’ll have change left over, but no soundcenter or stand. Or are you looking at an aftermarket integration of a new LG panel with the old soundcenter/stand?
If it was me, I’d probably go with the replacement screen, but the soundcenter, stand and sleek integration between them all are very important to me. I’d only go with the aftermarket option (assuming one exists) of mounting a different LG on the soundcenter if B&O could not help me. If your friend is considering dumping the entire Eclipse in favor of an LG, then I suppose audio quality and integration is not very important.
