jfrancis49
Forum Replies Created
- Posts
-
Hello,
I unfortunately had some health issues that slowed me down on sorting out the tracking force and arm balancing on my 4002, but I got back to it and hat is now working properly. I ended up taking the tonearm apart and lubricating it and then making sure it was not binding. I have adjusted the 33.33 and 45 rpm speeds and tried out a record. The record plays fine but I notice the tonearm is moving towards the sensor arm and plays at an angle. Is this a tracking sensor adjustment issue? They are both parallel to each other in the up and resting position. It sounds fine, but my other 4002 does not do this when playing a record.
This I believe is my last fix on this turntable.
John
Hello Mark,
Once again, my appreciation. I seem to have an unexpected amount of trouble getting the arm to balance. I will give it a go this weekend.
I thought maybe I should look at R88 and see if that should be adjusted. And that turned out to be the issue. Now all is working with the speed changes and set down, but I need to do some other adjustments. Balancing the tone arm is next. For whatever reason I have a hard time getting more weight forward to balance without it binding and pulling toward the spindle.
Hello Mark,
I do have the service manual and have looked at the flowchart. Don’t quite know how to follow some of the trouble shooting. I understand how to identify the different legs of a transistor, but not sure where to connect the other multimeter probe to. Afraid of shorting something.
I am currently traveling and won’t be back for a week.
Thanks Mark,
I have an extra board with the photodarlington transistor on it so just switched out that board. No change, the sensor arm still does not recognize where the record set down position should be and does not switch to 45 rpm as it travels toward the spindle. So something may be amiss on the main board still.
Hello Mark,
You were correct, the 45 rpm light does light up when I am able to use the cue button. And the solenoid does function. But the forward and reverse buttons don’t seem to activate those actionsn nor the stop button.
Hello Mark,
Thanks for the reply. Yes, the sensor arm lamp is working and pushed as far down in the sensor arm cavity as it will go. I understand there is some circuit connection here for the fault I am seeing. At start the sensor arm is not finding the record and or switching to 45 rpm as it travels inward. But I was thinking that the 45 rpm button on the keypad though should also function by lighting the 45 dial and turning the motor when pressed.
John
Hello Michael,
I don’t remember who posted it, but someone recommended using just a little baby oil on a soft cloth for the brushed aluminum. I have found that works nicely and just give it a good wipe down with a dry cloth to remove any excess. Regarding the plastic lid, if you have scratches, depending on the severity you will have to use sandpaper or abrasive polishes to remove them. There are several posts in older forums on doing that and some Google searching can lead to others. One thing I have learned is find a product that is an abrasive rather than a wax, the one that are mostly wax just hides scratches. Polishes made for restoring plastic are a good place to start.
Thank you Mark and Adam. Well, I learned something through this experience which is I didn’t think about bulb filament resistance as a factor in my thinking. The good news is I swapped out the tracking sensor today and it is working!
Lucky for me the issues related to this restoration have not required more than switching out a number of parts, soldering new components and adjustments to get this working. Serious trouble shooting is beyond my capabilities.
Thanks for your kind support!
John
Hello Mark,
Thank you for the post. I did have a lamp for the 33 and 45 speed adjustment, so I tried a continuity test on it and it showed no continuity. So I connected a 9V battery to it and it lit up. Not sure why my meter is not showing continuity. Crossing the leads does and my meter squeals like it should. Anyway I took the tracking sensor out of the BG 4002 and connected the leads to the 9 V battery, no light, bad bulb. I tried the other spare sensor I have and the bulb lights with the battery, so I will install that tomorrow and see if that takes care of it. Once again, thanks for your response.
John
Hello Tim,
Sorry for the delay. I very much appreciate the suggestion. I have decided I will first try learning the software to design the wheels based on my 1 good one and 3D print them. I have access to a 3D printer at my university and the software for drawing it is free. I may have found a source for the belts and am waiting for that to arrive. The only other sticking point may be clutch washers. I have not checked those out. But if the 3D printing doesn’t work out I will try your suggestion. Hopefully something good will come out of this I can share with other Beomaster 1600 people.
Thanks again!
John
