Beolink ML/NL version number? 1.4, 1.3

Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • #13542
    XavierItzmann
    BRONZE Member
      • Topics Started 21
      • Total Posts 147

      So, I need one of these as I was away during the transition years and all my old equipment is MasterLink and B&O no longer sells this critical component. Is it true that these are no longer consumer updatable? What’s a man to do then?

      If I buy one, is there a minimum version I should get? Are there substantial performance differences? I found an old post here in the forum that cited the final version number but then I lost it.

      Thanks in advance.

      #13558
      Tignum
      GOLD Member
        • Netherlands
        • Topics Started 8
        • Total Posts 361

        Hi Xavier,

        Both my BLCs are “1.4.3.19864, December 11, 2015” and they work fine.

        Hope this helps. Regards, Johan

        #13588
        XavierItzmann
        BRONZE Member
          • Topics Started 21
          • Total Posts 147

          Thank you Johan.

          I’ll be asking any sellers about the software version installed on their BeoLink Converter NL/ML, and will only buy if it is 1.4.3.19864 or higher.

          #13608
          Rolf2
          BRONZE Member
            • Germany
            • Topics Started 2
            • Total Posts 68

            Hello Xavier,

            Johan has mentioned what is to my knowledge the final sw version. Last year, I had to order a repair of one of my BLC ´ s and they needed to exchange the electronics completely. So, more or less a new unit, and it says sw is on 1.4.3.19864. You should be careful indeed, and buy only a BLC with the latest sw version. If it is on a lower level sw version, it may be so because of faulty electronics.

            The sw versions of the BLC are, from latest to older:

            1.4.3.19864 – Final version

            1.4.3.19816

            1.4.2.19611

            1.4.1.19522

            Those are the ones I know about.

            Kind regards,

            Rolf

            #13640
            XavierItzmann
            BRONZE Member
              • Topics Started 21
              • Total Posts 147

              Ahh, yes, Rolf, thanks for your detailed advice. The current range of Connected products is set by default on software “auto-update”, so when devices currently updated by B&O cease to be upgraded, most will be left on the final version.

              Which prompts me to ask… at the time the BLCs were current, did “auto-update” exist? Because then you’d be doubly right to question the full functionality of items being sold with less than the final version!

              (unless the devices were stored in a drawer, one might think).

              #13641
              Millemissen
              BRONZE Member
                • Flensborg————Danmark
                • Topics Started 21
                • Total Posts 1,025

                552E138C-71EF-49A3-A7F4-8916968CFCFB

                Just checked….

                MM

                #13696
                XavierItzmann
                BRONZE Member
                  • Topics Started 21
                  • Total Posts 147

                  Thanks, MM!

                  Since these BLC’s had recommended auto-update, most good ones should be on 1.4.3.19864!

                  Now I just have to get one.

                  #13713
                  Rolf2
                  BRONZE Member
                    • Germany
                    • Topics Started 2
                    • Total Posts 68

                    Go and grab one and enjoy your ML products working together with NL products!

                    Kind regards,

                    Rolf

                  Viewing 8 posts - 1 through 8 (of 8 total)
                  • You must be logged in to reply to this topic.