[gpv]

Thanks for the good advice I’ll try with a broken piece like yours.

[Die_Bogener]

The trick is the adjustment of the gear… 😉

 

[filip_kbh]

The gears are adjusted exactly like your picture shows.

[gpv]

I can’t figure out where lm 701 Led Module is written on the diagram to locate the interruption of the Vu Meter. can anyone help me figure out where it is?
Thank you.

[filip_kbh]

My problem with the loading mechanism is definitely the white worm wheel. The mechanism is smooth without it. Once it is inserted (correctly with the timing mark), the mechanism will become unstable and lock up in the right side. I am not sure if the spring part under it is assembled correctly. Any help is appreciated.

Also I noticed that the VX 5000 is getting very hot in the left corner away from the mechanism. Is that normal?

[gpv]

Maybe you mean on the right side where there is a heat sink, in this case it is normal

[filip_kbh]

Haha – no, I mean on the left side, seen from the front.

[Die_Bogener]

There is the 12V power regulator. It becomes really hot, even if the VX is ok and in standby. 60 degrees are quite normal, consuming 20W in standby… that’s a lot…

That’s why this VX had only a lifetime of some hundred hours. I had some VX5000 not surviving the first year in 1988…

The VX can be modified to save power. But this is a complete and very radical modification. A modified VX5000 consumes less than 10W, the VX7000 can be less 5W…

But… you can remove the analog tuner as a first step. There is no analog radio station on this planet any more… so, it’s a waste of space and electricity… and inside the tuner are also defect caps … 😉

Do you see the missing tuner? It is not necessary at all… just remove it. This works for the VX5000/5500/7000… less is more 🙂

Remove the tuner… or repair it. And when it is repaired, why put it in again? It’s a useless part…

 

 

 

[filip_kbh]

Here are a couple of videos of my loading mechanism problems – I don’t know how to embed the videos. Sorry that the speak is in Danish. What I basically say is that the mechanism is jammed, preventing the tape from being the item that unlocks the mechanism. However, if I turn the wheel under the machine, it will unlock and work.

https://youtu.be/gVU-HhJbuJs (mechanism out of machine)

and

https://youtu.be/wsfIXUdFwMU (mechanism in machine)

[Die_Bogener]

A worm drive will always yam the loading mechanism. It is impossible to turn it from outside.

Or it will break by forcing the cassette into the VX. What happened…

This is the trigger to load a cassette… moving the cassette 15mm inside the loading mechanism will trigger the switch on the drive board…

 

[gpv]

But this is not the vx5000 card, and then what happened to the socket for the flat cable that comes from the head

[filip_kbh]

I think mine looks identical.

[filip_kbh]

At this point I am ready to toss the whole thing and not spend more time on it. I think it’s the plastic part that I glued that is not completely accurate.

[filip_kbh]

Is it possible to get a new one 3D printed?

[Die_Bogener]

I still have some of them in stock… new.

[filip_kbh]

I will PM you.

[gpv]

Finally got the job done, my beocord vx500 is now working fine.
Many tracks were interrupted and I had to make jumpers, wire more than 200 capacitors, the battery etc…

[Die_Bogener]

New cassette loading unit online.

“VX5000 Kassetten Ladeschacht neu”

Last new part…

[filip_kbh]

Thank you, Martin – but I was lucky enough to get a VX7000 for free today, so I have taken the mechanism from that one.

However, I still have one problem:
The reel drive gear is driving me a bit insane. I cannot get it to touch the take up reel. I have looked in the service manual but there is definitely something that I am not seeing. Any tips? Seems like there is a plastic hook underneeth the right wheel that prevents the change.

Here is a video of the problem

 

[filip_kbh]

The FS arm is the blocker. It does move away if I turn the small motor to the right.
However, the damn thing wont either forward or reverse. I am clueless at this point.

[Author]

Posts